Jump to content

Recommended Posts

Posted
9 minutes ago, Six30 said:

So where and when is the swingers party and who is going ?

blam kill me now GIF

Posted
1 hour ago, Buckster said:

Swing arm is pretty good but powder coating will mean it will not deteriorate.

PXL_20250622_185558274_MP.thumb.jpg.74fe99f258a8a23acd2e822e98a8b8e5.jpg

Did you have to use much heat to drift the bearings out ?

Posted
3 minutes ago, boboneleg said:

Did you have to use much heat to drift the bearings out ?

I just pressed them out.

  • Like 1
Posted
4 hours ago, Buckster said:

Old design Vs new isolators.

PXL_20250622_190245266.NIGHT.thumb.jpg.b29a14ad031bbd1784a1bec171d36d1b.jpg

PXL_20250622_190233225.NIGHT.thumb.jpg.6ffe9f0a61652cd88a0bac8c2d73c72a.jpg

PXL_20250622_190207557_MP.thumb.jpg.d1b5dd7708259c160d60cdbe6f067326.jpg

New vs old you mean, you did it on purpose to trigger me.

Posted
6 hours ago, Pedro said:

New vs old you mean, you did it on purpose to trigger me.

It worked didn’t it?

Posted
20 hours ago, Buckster said:

Swing arm is pretty good but powder coating will mean it will not deteriorate.

PXL_20250622_185558274_MP.thumb.jpg.74fe99f258a8a23acd2e822e98a8b8e5.jpg

Get some rust eater/protector inside after the power coat's done, then it might last forever.

Posted
3 hours ago, Catteeclan said:

Get some rust eater/protector inside after the power coat's done, then it might last forever.

I could probably get some Lanoguard in there through the drain holes.

  • Like 3
Posted
1 hour ago, Buckster said:

I could probably get some Lanoguard in there through the drain holes.

Seriously sticky shit that Lanoguard, the swinging arm on my CBF was covered in it when I got the bike, still some on there now 12 months and 6k later.  

Posted

My wheel is ready to go, New bearings, spacers, cush drive rubbers. I am letting the swing arm inner dry before refitting 

Posted
1 hour ago, Buckster said:

My wheel is ready to go, New bearings, spacers, cush drive rubbers. I am letting the swing arm inner dry before refitting 

Good progress but what have you been doing with that hoover pipe.

  • Haha 2
Posted
1 hour ago, Catteeclan said:

Good progress but what have you been doing with that hoover pipe.

I got that from an Arab friend.

  • Haha 1
Posted
14 hours ago, Buckster said:

I got that from an Arab friend.

I hope you cleaned it first ...... :classic_unsure:

Posted
3 minutes ago, boboneleg said:

I hope you cleaned it first ...... :classic_unsure:

It was on his Honda.

Posted

New swing arm bearings and spacers are in, it's nearly as hot outside as where @Six30 will go when he pegs it. Just cooling down then the swing arm goes back in with the new improved swing arm pivot.

PXL_20250629_131948690.thumb.jpg.36e33c0f2badabd82e03016d3589443e.jpg

  • Like 2
  • Haha 1
Posted

Swing arm is in, pain in the arse getting it all lined up, I would have had zero chance without the new lift.

  • Like 1
Posted

New back wheel is in, I will finish it off during the week.

Posted
14 minutes ago, Pedro said:

Do you have any alignment tools or is it done by sight?

I have a laser.

Posted

Bike is all back together, I need to realign the front engine mount but it’s pissing down now. That will be a ten minute job tomorrow.

  • Like 4
Posted

So today was the shakedown ride, I was only going to do fifty miles but did twice that, it was too nice out. Went exploring the kingdom of Fife. I aimed the bike at every joint in the road, every rut, every bit of banding to see if it would get upset but it shrugged it all off. It feels like I have new tyres. A little bit of extra vibration at tickover and at about 3000 rpm which was expected, more a buzz than anything, that should disappear after 300 to 500 miles.

I was definitely barreling into corners on the way back, the handling feels rock solid.

  • Like 4

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...

Important Information

Privacy Policy