Six30 Posted June 22 Share Posted June 22 So where and when is the swingers party and who is going ? Link to comment Share on other sites More sharing options...
Buckster Posted June 22 Author Share Posted June 22 9 minutes ago, Six30 said: So where and when is the swingers party and who is going ? Link to comment Share on other sites More sharing options...
boboneleg Posted June 22 Share Posted June 22 1 hour ago, Buckster said: Swing arm is pretty good but powder coating will mean it will not deteriorate. Did you have to use much heat to drift the bearings out ? Link to comment Share on other sites More sharing options...
Buckster Posted June 22 Author Share Posted June 22 3 minutes ago, boboneleg said: Did you have to use much heat to drift the bearings out ? I just pressed them out. 1 Link to comment Share on other sites More sharing options...
Pedro Posted June 22 Share Posted June 22 4 hours ago, Buckster said: Old design Vs new isolators. New vs old you mean, you did it on purpose to trigger me. Link to comment Share on other sites More sharing options...
Buckster Posted June 23 Author Share Posted June 23 6 hours ago, Pedro said: New vs old you mean, you did it on purpose to trigger me. It worked didn’t it? Link to comment Share on other sites More sharing options...
Catteeclan Posted June 23 Share Posted June 23 20 hours ago, Buckster said: Swing arm is pretty good but powder coating will mean it will not deteriorate. Get some rust eater/protector inside after the power coat's done, then it might last forever. Link to comment Share on other sites More sharing options...
Buckster Posted June 23 Author Share Posted June 23 3 hours ago, Catteeclan said: Get some rust eater/protector inside after the power coat's done, then it might last forever. I could probably get some Lanoguard in there through the drain holes. 3 Link to comment Share on other sites More sharing options...
Saul Posted June 23 Share Posted June 23 1 hour ago, Buckster said: I could probably get some Lanoguard in there through the drain holes. Seriously sticky shit that Lanoguard, the swinging arm on my CBF was covered in it when I got the bike, still some on there now 12 months and 6k later. Link to comment Share on other sites More sharing options...
boboneleg Posted June 24 Share Posted June 24 I've been getting my underside washed today before I swathe it Lanoguard 3 Link to comment Share on other sites More sharing options...
Buckster Posted June 26 Author Share Posted June 26 4 Link to comment Share on other sites More sharing options...
Buckster Posted June 27 Author Share Posted June 27 My wheel is ready to go, New bearings, spacers, cush drive rubbers. I am letting the swing arm inner dry before refitting Link to comment Share on other sites More sharing options...
Catteeclan Posted June 27 Share Posted June 27 1 hour ago, Buckster said: My wheel is ready to go, New bearings, spacers, cush drive rubbers. I am letting the swing arm inner dry before refitting Good progress but what have you been doing with that hoover pipe. 1 Link to comment Share on other sites More sharing options...
Buckster Posted June 27 Author Share Posted June 27 1 hour ago, Catteeclan said: Good progress but what have you been doing with that hoover pipe. I got that from an Arab friend. 1 Link to comment Share on other sites More sharing options...
boboneleg Posted June 28 Share Posted June 28 14 hours ago, Buckster said: I got that from an Arab friend. I hope you cleaned it first ...... Link to comment Share on other sites More sharing options...
Buckster Posted June 28 Author Share Posted June 28 3 minutes ago, boboneleg said: I hope you cleaned it first ...... It was on his Honda. Link to comment Share on other sites More sharing options...
Buckster Posted June 29 Author Share Posted June 29 New swing arm bearings and spacers are in, it's nearly as hot outside as where @Six30 will go when he pegs it. Just cooling down then the swing arm goes back in with the new improved swing arm pivot. 2 Link to comment Share on other sites More sharing options...
Buckster Posted June 29 Author Share Posted June 29 Swing arm is in, pain in the arse getting it all lined up, I would have had zero chance without the new lift. 1 Link to comment Share on other sites More sharing options...
Buckster Posted June 29 Author Share Posted June 29 New back wheel is in, I will finish it off during the week. Link to comment Share on other sites More sharing options...
Pedro Posted June 29 Share Posted June 29 Do you have any alignment tools or is it done by sight? Link to comment Share on other sites More sharing options...
Buckster Posted June 29 Author Share Posted June 29 14 minutes ago, Pedro said: Do you have any alignment tools or is it done by sight? I have a laser. Link to comment Share on other sites More sharing options...
Buckster Posted 6 hours ago Author Share Posted 6 hours ago Bike is all back together, I need to realign the front engine mount but it’s pissing down now. That will be a ten minute job tomorrow. 2 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now